APRS.ro MAP

Reset

reset

ED1ZAP-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAP-3. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V.BAT*	C.BAT*	C.LOAD*	TEMP*	V.PLS*
1738323557	14 V	16.04 A	2.42 A	8 C	28.8 V
1738322656	13.4 V	15.72 A	2.26 A	7.5 C	28.8 V
1738321755	13 V	11.36 A	2.42 A	7 C	19 V
1738320854	12.7 V	5.64 A	2.34 A	7 C	31 V
1738319953	12.4 V	2.42 A	2.66 A	6 C	30 V
1738308046	11.9 V	0 A	1.37 A	5.5 C	3.2 V
1738306245	11.9 V	0 A	1.29 A	5.5 C	0 V
1738305344	11.9 V	0 A	1.45 A	6 C	0 V
1738304443	11.9 V	0 A	1.37 A	6 C	0 V
1738303542	11.9 V	0 A	1.61 A	6 C	0 V
1738302641	11.9 V	0 A	1.29 A	6 C	0 V
1738301740	11.9 V	0 A	1.61 A	6 C	0 V
1738300840	11.9 V	0 A	1.29 A	6 C	0 V
1738299939	11.9 V	0 A	1.61 A	6 C	0 V
1738299038	11.9 V	0 A	1.29 A	6 C	0 V
1738298137	11.9 V	0 A	1.53 A	6 C	0 V
1738297236	11.9 V	0 A	1.37 A	6 C	0 V
1738296335	11.9 V	0 A	1.53 A	6 C	0 V
1738295434	11.9 V	0 A	1.61 A	6 C	0 V
1738294534	11.9 V	0 A	1.61 A	6.5 C	0 V
1738293633	11.9 V	0 A	1.29 A	6.5 C	0 V
1738292733	11.9 V	0 A	1.53 A	6.5 C	0 V
1738291831	12 V	0 A	1.37 A	6.5 C	0 V
1738290930	12 V	0 A	1.53 A	6.5 C	0 V
1738290029	12 V	0 A	1.29 A	6.5 C	0 V

*Used Equation Coefficients:

V.BAT: 0, 0.1, 0

C.BAT: 0, 0.0806, 0

C.LOAD: 0, 0.0806, 0

TEMP: 0, 0.5, -64

V.PLS: 0, 0.2, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)