APRS.ro MAP

Reset

reset

DB0LEI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0LEI. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1737241540	13.8 Volt	230 Pkt	120 Pkt	86 Pcnt
1737240339	13.8 Volt	260 Pkt	120 Pkt	83 Pcnt
1737239138	13.8 Volt	270 Pkt	120 Pkt	83 Pcnt
1737237937	13.72 Volt	260 Pkt	120 Pkt	83 Pcnt
1737236736	13.8 Volt	270 Pkt	130 Pkt	88 Pcnt
1737235535	13.8 Volt	270 Pkt	140 Pkt	91 Pcnt
1737234333	13.8 Volt	260 Pkt	130 Pkt	93 Pcnt
1737233132	13.8 Volt	230 Pkt	120 Pkt	92 Pcnt
1737231931	13.8 Volt	210 Pkt	120 Pkt	90 Pcnt
1737230730	13.8 Volt	210 Pkt	120 Pkt	90 Pcnt
1737229529	13.8 Volt	240 Pkt	140 Pkt	90 Pcnt
1737228328	13.8 Volt	300 Pkt	160 Pkt	91 Pcnt
1737227127	13.8 Volt	350 Pkt	190 Pkt	92 Pcnt
1737225925	13.8 Volt	360 Pkt	180 Pkt	92 Pcnt
1737224724	13.65 Volt	330 Pkt	160 Pkt	91 Pcnt
1737223523	13.8 Volt	260 Pkt	130 Pkt	89 Pcnt
1737222322	13.51 Volt	260 Pkt	140 Pkt	92 Pcnt
1737221121	13.8 Volt	230 Pkt	130 Pkt	91 Pcnt
1737219920	13.8 Volt	220 Pkt	120 Pkt	91 Pcnt
1737218718	13.8 Volt	190 Pkt	100 Pkt	90 Pcnt
1737217517	13.8 Volt	200 Pkt	110 Pkt	94 Pcnt
1737216316	13.8 Volt	260 Pkt	140 Pkt	97 Pcnt
1737215115	13.8 Volt	290 Pkt	150 Pkt	97 Pcnt
1737213914	13.8 Volt	290 Pkt	150 Pkt	95 Pcnt
1737212713	13.8 Volt	290 Pkt	160 Pkt	95 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.073, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)