APRS.ro MAP

Reset

reset

ED1ZAD-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAD-3. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RX1h*	DG1h*	Eff1h*
1738325221	650 Pkt	70 Pkt	85 Pcnt
1738324621	680 Pkt	70 Pkt	84 Pcnt
1738324020	690 Pkt	60 Pkt	84 Pcnt
1738323419	700 Pkt	60 Pkt	83 Pcnt
1738322819	680 Pkt	60 Pkt	83 Pcnt
1738322218	680 Pkt	60 Pkt	83 Pcnt
1738321618	640 Pkt	60 Pkt	82 Pcnt
1738321017	590 Pkt	60 Pkt	82 Pcnt
1738320419	560 Pkt	60 Pkt	81 Pcnt
1738319816	560 Pkt	60 Pkt	81 Pcnt
1738319215	570 Pkt	60 Pkt	81 Pcnt
1738318615	570 Pkt	60 Pkt	81 Pcnt
1738318014	590 Pkt	70 Pkt	81 Pcnt
1738317414	610 Pkt	80 Pkt	80 Pcnt
1738316815	570 Pkt	80 Pkt	79 Pcnt
1738316213	610 Pkt	80 Pkt	77 Pcnt
1738315613	600 Pkt	80 Pkt	77 Pcnt
1738315011	530 Pkt	70 Pkt	72 Pcnt
1738314411	530 Pkt	60 Pkt	71 Pcnt
1738313210	520 Pkt	60 Pkt	71 Pcnt
1738312609	490 Pkt	60 Pkt	74 Pcnt
1738312008	500 Pkt	80 Pkt	75 Pcnt
1738311408	560 Pkt	80 Pkt	81 Pcnt
1738310807	550 Pkt	80 Pkt	83 Pcnt
1738310207	530 Pkt	90 Pkt	82 Pcnt

*Used Equation Coefficients:

RX1h: 0, 10, 0

DG1h: 0, 10, 0

Eff1h: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)