APRS.ro MAP

Reset

reset

YO3JAZ-NC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3JAZ-NC. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Load*	RSSI*	Vcc*
1732415016	11.5 C	7.6 %	-57 dBm	3.44 V
1732414656	11.5 C	7.6 %	-56 dBm	3.44 V
1732414296	11.5 C	7.6 %	-56 dBm	3.44 V
1732413936	11.5 C	7.2 %	-56 dBm	3.44 V
1732413576	11.5 C	7.2 %	-57 dBm	3.44 V
1732413216	11.5 C	7.2 %	-56 dBm	3.44 V
1732412856	11.5 C	7.2 %	-58 dBm	3.44 V
1732412496	11.5 C	7.2 %	-56 dBm	3.44 V
1732412136	11.5 C	7.2 %	-56 dBm	3.44 V
1732411776	11.5 C	7.2 %	-56 dBm	3.44 V
1732411416	12 C	7.2 %	-57 dBm	3.44 V
1732411056	12 C	7.6 %	-56 dBm	3.44 V
1732410696	12 C	7.6 %	-56 dBm	3.44 V
1732410336	12 C	7.6 %	-56 dBm	3.43 V
1732409976	12 C	7.2 %	-56 dBm	3.44 V
1732409616	12 C	7.6 %	-56 dBm	3.44 V
1732409256	12 C	7.2 %	-56 dBm	3.43 V
1732408896	12 C	7.6 %	-57 dBm	3.44 V
1732408536	12 C	7.6 %	-57 dBm	3.43 V
1732408176	12 C	7.2 %	-57 dBm	3.43 V
1732407816	12 C	7.6 %	-56 dBm	3.44 V
1732407456	12 C	8.4 %	-57 dBm	3.44 V
1732407096	12 C	7.6 %	-57 dBm	3.44 V
1732406736	12 C	7.6 %	-57 dBm	3.45 V
1732406376	12 C	7.6 %	-56 dBm	3.44 V

*Used Equation Coefficients:

Temp: 0, 0.5, -25

Power: 0, 20, 0

Load: 0, 0.4, 0

RSSI: 0, -1, 0

Vcc: 0, 0.01, 2.5

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)