APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

LZ2KAC-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ2KAC-5. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1732272147	1 Pkt	-61 dBm	14.64 V
1732270337	0 Pkt	-61 dBm	14.66 V
1732268527	1 Pkt	-62 dBm	14.64 V
1732266717	4 Pkt	-60 dBm	14.64 V
1732264907	1 Pkt	-60 dBm	14.64 V
1732263097	0 Pkt	-60 dBm	14.62 V
1732261287	1 Pkt	-61 dBm	14.64 V
1732259477	0 Pkt	-61 dBm	14.66 V
1732257667	1 Pkt	-60 dBm	14.64 V
1732255857	3 Pkt	-60 dBm	14.62 V
1732254047	0 Pkt	-60 dBm	14.64 V
1732252237	0 Pkt	-61 dBm	14.64 V
1732250427	0 Pkt	-61 dBm	14.64 V
1732248617	0 Pkt	-62 dBm	14.62 V
1732246807	0 Pkt	-60 dBm	14.6 V
1732244997	0 Pkt	-60 dBm	14.62 V
1732243187	0 Pkt	-61 dBm	14.62 V
1732241377	0 Pkt	-60 dBm	14.62 V
1732239567	0 Pkt	-60 dBm	14.62 V
1732237757	0 Pkt	-59 dBm	14.64 V
1732235947	1 Pkt	-60 dBm	14.64 V
1732234137	1 Pkt	-62 dBm	14.64 V
1732232327	1 Pkt	-60 dBm	14.64 V
1732230517	1 Pkt	-60 dBm	14.62 V
1732228707	2 Pkt	-60 dBm	14.64 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)