APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

OK1RPL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1RPL-1. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Dg1h*	Eff1h*
1732258778	300 Pkt	110 Pkt	84 Pcnt
1732257877	320 Pkt	120 Pkt	84 Pcnt
1732256976	340 Pkt	140 Pkt	85 Pcnt
1732256075	350 Pkt	140 Pkt	85 Pcnt
1732255174	350 Pkt	150 Pkt	87 Pcnt
1732254274	320 Pkt	130 Pkt	86 Pcnt
1732253373	300 Pkt	120 Pkt	82 Pcnt
1732252472	280 Pkt	110 Pkt	81 Pcnt
1732251571	270 Pkt	100 Pkt	77 Pcnt
1732250670	270 Pkt	100 Pkt	76 Pcnt
1732249769	270 Pkt	100 Pkt	75 Pcnt
1732248868	270 Pkt	100 Pkt	74 Pcnt
1732247968	260 Pkt	100 Pkt	71 Pcnt
1732247067	240 Pkt	90 Pkt	69 Pcnt
1732246166	250 Pkt	90 Pkt	71 Pcnt
1732245265	260 Pkt	90 Pkt	73 Pcnt
1732244364	260 Pkt	90 Pkt	77 Pcnt
1732243463	270 Pkt	100 Pkt	80 Pcnt
1732242562	260 Pkt	100 Pkt	74 Pcnt
1732241661	270 Pkt	100 Pkt	68 Pcnt
1732240761	290 Pkt	100 Pkt	65 Pcnt
1732239860	290 Pkt	100 Pkt	64 Pcnt
1732238959	300 Pkt	100 Pkt	68 Pcnt
1732238058	290 Pkt	100 Pkt	72 Pcnt
1732237157	260 Pkt	90 Pkt	76 Pcnt

*Used Equation Coefficients:

Temp: 0, 0, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)