APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

IR3EO-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR3EO-11. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1732244271	144 Pkt	910 Pkt	12.09 Volt
1732243971	107 Pkt	900 Pkt	12.01 Volt
1732243671	114 Pkt	920 Pkt	12.09 Volt
1732243371	133 Pkt	940 Pkt	12.09 Volt
1732243071	128 Pkt	940 Pkt	12.09 Volt
1732242771	132 Pkt	930 Pkt	12.09 Volt
1732242471	147 Pkt	960 Pkt	12.09 Volt
1732242171	123 Pkt	950 Pkt	12.01 Volt
1732241871	165 Pkt	960 Pkt	12.09 Volt
1732241571	148 Pkt	950 Pkt	12.01 Volt
1732241271	127 Pkt	940 Pkt	12.09 Volt
1732240971	146 Pkt	950 Pkt	12.01 Volt
1732240671	164 Pkt	960 Pkt	12.09 Volt
1732240371	147 Pkt	950 Pkt	12.09 Volt
1732240074	152 Pkt	940 Pkt	12.09 Volt
1732239771	128 Pkt	910 Pkt	12.01 Volt
1732239471	149 Pkt	910 Pkt	12.09 Volt
1732239171	166 Pkt	920 Pkt	12.09 Volt
1732238871	149 Pkt	910 Pkt	12.09 Volt
1732238571	132 Pkt	930 Pkt	12.01 Volt
1732238271	144 Pkt	940 Pkt	12.09 Volt
1732237971	148 Pkt	930 Pkt	12.09 Volt
1732237671	134 Pkt	950 Pkt	12.09 Volt
1732237371	153 Pkt	980 Pkt	12.01 Volt
1732237071	149 Pkt	1000 Pkt	12.09 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Volt: 0, 0.079, 0

DgR: 0, 0.001, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)