APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

IQ3TS-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ3TS-11. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1732252112	60 Pkt	360 Pkt	14.3 Volt
1732251812	51 Pkt	340 Pkt	14.3 Volt
1732251512	47 Pkt	360 Pkt	14.3 Volt
1732251212	46 Pkt	360 Pkt	14.3 Volt
1732250912	42 Pkt	360 Pkt	14.3 Volt
1732250612	49 Pkt	360 Pkt	14.3 Volt
1732250312	51 Pkt	370 Pkt	14.3 Volt
1732250012	50 Pkt	370 Pkt	14.3 Volt
1732249712	58 Pkt	380 Pkt	14.3 Volt
1732249412	61 Pkt	370 Pkt	14.3 Volt
1732249112	72 Pkt	380 Pkt	14.3 Volt
1732248812	53 Pkt	380 Pkt	14.3 Volt
1732248512	63 Pkt	380 Pkt	14.3 Volt
1732248212	70 Pkt	370 Pkt	14.3 Volt
1732247912	60 Pkt	360 Pkt	14.3 Volt
1732247612	46 Pkt	360 Pkt	14.3 Volt
1732247312	41 Pkt	360 Pkt	14.3 Volt
1732247012	52 Pkt	360 Pkt	14.3 Volt
1732246712	62 Pkt	360 Pkt	14.3 Volt
1732246412	55 Pkt	350 Pkt	14.3 Volt
1732246112	68 Pkt	350 Pkt	14.3 Volt
1732245812	68 Pkt	350 Pkt	14.3 Volt
1732245512	63 Pkt	350 Pkt	14.3 Volt
1732245212	53 Pkt	360 Pkt	14.3 Volt
1732244912	42 Pkt	370 Pkt	14.3 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

DgR: 0, 0.001, 0

Volt: 0, 0.079, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)