APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

YO3FVR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FVR-1. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Tin*
1732267500	12.6 Volt	33 Pcnt	4.5 C
1732266900	12.6 Volt	50 Pcnt	4.5 C
1732266300	12.6 Volt	50 Pcnt	4 C
1732265700	12.38 Volt	66 Pcnt	4 C
1732265100	12.45 Volt	83 Pcnt	4 C
1732264500	12.38 Volt	83 Pcnt	4 C
1732263902	12.3 Volt	100 Pcnt	4 C
1732263900	12.3 Volt	100 Pcnt	4 C
1732263300	12.38 Volt	100 Pcnt	4 C
1732262700	12.45 Volt	100 Pcnt	4 C
1732262100	12.3 Volt	100 Pcnt	4 C
1732261500	12.38 Volt	50 Pcnt	3.5 C
1732261202	12.38 Volt	50 Pcnt	3.5 C
1732260900	12.38 Volt	66 Pcnt	3.5 C
1732260302	12.23 Volt	80 Pcnt	3.5 C
1732260300	12.23 Volt	80 Pcnt	3.5 C
1732259700	12.3 Volt	71 Pcnt	3.5 C
1732259402	12.3 Volt	75 Pcnt	3.5 C
1732259100	12.3 Volt	66 Pcnt	3.5 C
1732258502	12.23 Volt	62 Pcnt	3.5 C
1732258500	12.23 Volt	62 Pcnt	3.5 C
1732257900	12.3 Volt	62 Pcnt	3.5 C
1732257300	12.3 Volt	63 Pcnt	3.5 C
1732256702	12.23 Volt	50 Pcnt	3.5 C
1732256700	12.23 Volt	50 Pcnt	3.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Vsol: 0, 0.075, 0

Isol: 0, 0.1, 0

Eff1h: 0, 1, 0

Tin: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)