APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

SR9NCI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NCI. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1732281282	109 Pkt	3 Pkt	0 Pkt
1732280678	111 Pkt	4 Pkt	0 Pkt
1732280073	114 Pkt	6 Pkt	0 Pkt
1732278858	109 Pkt	2 Pkt	0 Pkt
1732278255	123 Pkt	4 Pkt	0 Pkt
1732277039	93 Pkt	4 Pkt	1 Pkt
1732276435	112 Pkt	3 Pkt	0 Pkt
1732275831	103 Pkt	3 Pkt	0 Pkt
1732275227	109 Pkt	9 Pkt	2 Pkt
1732274616	101 Pkt	4 Pkt	0 Pkt
1732274011	104 Pkt	2 Pkt	0 Pkt
1732273408	113 Pkt	4 Pkt	0 Pkt
1732272803	132 Pkt	7 Pkt	1 Pkt
1732272193	100 Pkt	4 Pkt	0 Pkt
1732271587	111 Pkt	2 Pkt	0 Pkt
1732270378	103 Pkt	7 Pkt	0 Pkt
1732269767	87 Pkt	3 Pkt	0 Pkt
1732269163	115 Pkt	3 Pkt	0 Pkt
1732268559	90 Pkt	4 Pkt	1 Pkt
1732267956	105 Pkt	7 Pkt	0 Pkt
1732267344	98 Pkt	5 Pkt	1 Pkt
1732266739	90 Pkt	2 Pkt	0 Pkt
1732266136	105 Pkt	4 Pkt	0 Pkt
1732264921	112 Pkt	5 Pkt	1 Pkt
1732264316	125 Pkt	6 Pkt	3 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)