APRS.ro MAP

Reset

reset

YO3FBD-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FBD-11. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp_interioara*	Temp_exterioara*	Temp_TX_RoLink*
1732429865	6.4 C	-0.2 C	6.9 C
1732429271	5.2 C	-0.2 C	5.9 C
1732428665	4.1 C	-1.4 C	5.2 C
1732428065	3.1 C	-2.7 C	4.4 C
1732427471	1.8 C	-2.9 C	3.9 C
1732426865	0.9 C	-3.8 C	4.1 C
1732426265	0.7 C	-5.1 C	4.9 C
1732425671	1.1 C	-5.2 C	6.6 C
1732425066	1.8 C	-5 C	10.1 C
1732424466	2.4 C	-4.6 C	19.6 C
1732423871	2.5 C	-4.3 C	21.5 C
1732423266	2.4 C	-4.6 C	21.6 C
1732422666	2.2 C	-5 C	21.2 C
1732422071	2 C	-5 C	20.9 C
1732421466	1.9 C	-5.8 C	20.9 C
1732420866	1.8 C	-4.9 C	20.2 C
1732420271	1.7 C	-4.9 C	18.9 C
1732419666	1.3 C	-4.1 C	13.9 C
1732419066	1 C	-4 C	4.5 C
1732418471	1.1 C	-4.2 C	4.6 C
1732417871	1.2 C	-3.6 C	4.8 C
1732417266	1.4 C	-3.7 C	4.8 C
1732416671	1.6 C	-3.6 C	4.9 C
1732416066	1.6 C	-3.5 C	4.9 C
1732415466	1.6 C	-3.6 C	4.9 C

*Used Equation Coefficients:

Temp_interioara: 0, 1, -100

Temp_exterioara: 0, 1, -100

Temp_TX_RoLink: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)