APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

LZ2SMX-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ2SMX-4. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Tbsmt*	Rh*	Tfl1*	Tktcn*	Tloft*
1732246707	13 C	55 %	13 C	12 C	6 C
1732245866	13 C	55 %	13 C	12 C	6 C
1732245024	13 C	55 %	13 C	12 C	6 C
1732244182	13 C	55 %	13 C	12 C	6 C
1732243341	13 C	55 %	13 C	12 C	6 C
1732242501	13 C	55 %	13 C	12 C	6 C
1732241660	13 C	55 %	13 C	12 C	6 C
1732240819	13 C	55 %	13 C	12 C	6 C
1732239968	13 C	55 %	13 C	12 C	6 C
1732239127	13 C	55 %	13 C	12 C	6 C
1732238284	13 C	55 %	13 C	12 C	7 C
1732237444	13 C	55 %	13 C	12 C	6 C
1732236603	13 C	55 %	13 C	12 C	7 C
1732235760	13 C	55 %	13 C	12 C	7 C
1732234919	13 C	55 %	13 C	12 C	7 C
1732234078	13 C	55 %	13 C	12 C	7 C
1732233236	13 C	55 %	13 C	12 C	7 C
1732232395	13 C	55 %	13 C	12 C	7 C
1732231545	13 C	55 %	13 C	12 C	7 C
1732230703	13 C	55 %	13 C	12 C	7 C
1732229862	13 C	55 %	13 C	12 C	7 C
1732229021	13 C	55 %	13 C	12 C	7 C
1732228180	13 C	55 %	12 C	12 C	8 C
1732227339	13 C	56 %	13 C	12 C	8 C
1732226498	13 C	56 %	13 C	12 C	8 C

*Used Equation Coefficients:

Tbsmt: 0, 1, 0

Rh: 0, 1, 0

Tfl1: 0, 1, 0

Tktcn: 0, 1, 0

Tloft: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)