APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

SR5KAC-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR5KAC-2. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Avg 10m*	Avg 10m*	RxPkts*	IGateDropRx*	TxPkts*
1732281667	0.01 Volt	0.02 Pkt	4 Pkt	2 Pcnt	15
1732280467	0.01 Volt	0.02 Pkt	4 Pkt	1 Pcnt	16
1732279267	0.01 Volt	0.02 Pkt	5 Pkt	2 Pcnt	17
1732278067	0.01 Volt	0.02 Pkt	4 Pkt	2 Pcnt	15
1732276867	0.01 Volt	0.02 Pkt	4 Pkt	1 Pcnt	17
1732275667	0.01 Volt	0.02 Pkt	6 Pkt	2 Pcnt	17
1732274467	0.01 Volt	0.02 Pkt	6 Pkt	2 Pcnt	16
1732273267	0.01 Volt	0.02 Pkt	5 Pkt	2 Pcnt	16
1732272067	0.01 Volt	0.03 Pkt	6 Pkt	2 Pcnt	21
1732270867	0.01 Volt	0.02 Pkt	4 Pkt	1 Pcnt	16
1732269667	0.01 Volt	0.02 Pkt	5 Pkt	2 Pcnt	17
1732268467	0.01 Volt	0.02 Pkt	6 Pkt	2 Pcnt	15
1732267267	0.01 Volt	0.02 Pkt	6 Pkt	2 Pcnt	17
1732266067	0.01 Volt	0.02 Pkt	6 Pkt	2 Pcnt	16

*Used Equation Coefficients:

Avg 10m: 0, 0.005, 0

RxPkts: 0, 1, 0

IGateDropRx: 0, 1, 0

TxPkts: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)