APRS.ro MAP

Reset

reset

UR7D-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR7D-1. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*
1732414054	12.53 Volt	1280 Pkt	480 Pkt
1732413756	12.53 Volt	1280 Pkt	470 Pkt
1732413754	12.53 Volt	1280 Pkt	470 Pkt
1732413454	12.53 Volt	1280 Pkt	490 Pkt
1732413155	12.53 Volt	1280 Pkt	480 Pkt
1732413154	12.53 Volt	1280 Pkt	480 Pkt
1732412854	12.53 Volt	1280 Pkt	490 Pkt
1732412555	12.53 Volt	1280 Pkt	520 Pkt
1732412554	12.53 Volt	1280 Pkt	520 Pkt
1732412255	12.53 Volt	1280 Pkt	570 Pkt
1732411955	12.53 Volt	1280 Pkt	580 Pkt
1732411955	12.53 Volt	1280 Pkt	580 Pkt
1732411654	12.53 Volt	1280 Pkt	610 Pkt
1732411356	12.53 Volt	1280 Pkt	610 Pkt
1732411355	12.53 Volt	1280 Pkt	610 Pkt
1732411055	12.53 Volt	1280 Pkt	610 Pkt
1732410756	12.53 Volt	1280 Pkt	590 Pkt
1732410755	12.53 Volt	1280 Pkt	590 Pkt
1732410455	12.53 Volt	1280 Pkt	590 Pkt
1732410157	12.53 Volt	1280 Pkt	570 Pkt
1732410155	12.53 Volt	1280 Pkt	570 Pkt
1732409855	12.53 Volt	1280 Pkt	550 Pkt
1732409557	12.6 Volt	1280 Pkt	520 Pkt
1732409556	12.6 Volt	1280 Pkt	520 Pkt
1732409255	12.53 Volt	1280 Pkt	500 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)