APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

SQ7BCZ-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ7BCZ-14. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Temp*
1732261728	12.75 Volt	4 Pkt	27.5 C
1732259928	12.75 Volt	5 Pkt	27.5 C
1732258128	12.75 Volt	4 Pkt	27.5 C
1732256328	12.75 Volt	3 Pkt	27 C
1732254528	12.75 Volt	3 Pkt	25.5 C
1732252728	12.75 Volt	3 Pkt	15.5 C
1732250928	12.75 Volt	3 Pkt	28.5 C
1732249128	12.68 Volt	3 Pkt	28.5 C
1732247328	12.75 Volt	3 Pkt	28 C
1732245528	12.75 Volt	4 Pkt	28.5 C
1732243728	12.75 Volt	3 Pkt	28 C
1732241928	12.75 Volt	3 Pkt	28.5 C
1732240128	12.75 Volt	3 Pkt	28.5 C
1732238328	12.75 Volt	3 Pkt	28 C
1732236528	12.75 Volt	3 Pkt	28 C
1732234728	12.75 Volt	3 Pkt	28 C
1732232928	12.75 Volt	3 Pkt	28 C
1732231129	12.75 Volt	3 Pkt	28 C
1732229329	12.68 Volt	3 Pkt	28 C
1732227529	12.68 Volt	3 Pkt	28 C
1732225729	12.75 Volt	3 Pkt	27.5 C
1732223929	12.75 Volt	3 Pkt	26.5 C
1732222129	12.75 Volt	3 Pkt	27 C
1732220329	12.75 Volt	3 Pkt	27 C
1732218529	12.75 Volt	3 Pkt	26.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 1, 0

Dg1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)