APRS.ro MAP

Reset

reset

SR9POD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9POD. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	T_in*	Rx1h*	Dg1h*
1734632556	13.65 Volt	15 C	320 Pkt	100 Pkt
1734631954	13.65 Volt	15 C	310 Pkt	100 Pkt
1734631354	13.65 Volt	15 C	340 Pkt	110 Pkt
1734630754	13.65 Volt	15 C	400 Pkt	130 Pkt
1734630154	13.65 Volt	15 C	460 Pkt	160 Pkt
1734629554	13.65 Volt	15 C	450 Pkt	150 Pkt
1734628954	13.65 Volt	15 C	450 Pkt	160 Pkt
1734628354	13.65 Volt	15 C	470 Pkt	170 Pkt
1734627755	13.65 Volt	15 C	420 Pkt	150 Pkt
1734627154	13.65 Volt	15.5 C	340 Pkt	120 Pkt
1734626554	13.65 Volt	15.5 C	300 Pkt	100 Pkt
1734625954	13.65 Volt	15.5 C	350 Pkt	130 Pkt
1734625355	13.65 Volt	15.5 C	340 Pkt	120 Pkt
1734624755	13.65 Volt	15.5 C	330 Pkt	120 Pkt
1734624154	13.65 Volt	15.5 C	370 Pkt	130 Pkt
1734623554	13.65 Volt	15.5 C	380 Pkt	120 Pkt
1734622955	13.65 Volt	15.5 C	370 Pkt	120 Pkt
1734622354	13.65 Volt	15.5 C	310 Pkt	80 Pkt
1734621755	13.65 Volt	15.5 C	300 Pkt	80 Pkt
1734621155	13.65 Volt	15.5 C	300 Pkt	70 Pkt
1734620555	13.65 Volt	15 C	300 Pkt	80 Pkt
1734619954	13.65 Volt	15 C	320 Pkt	90 Pkt
1734619354	13.65 Volt	15.5 C	360 Pkt	100 Pkt
1734618754	13.65 Volt	15.5 C	390 Pkt	120 Pkt
1734618154	13.65 Volt	15.5 C	400 Pkt	120 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

T_in: 0, 0.5, -64

T_out: 0, 1, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)