APRS.ro MAP

Reset

reset

SP8EBC-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8EBC-11. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tx10min*	Vbatt*	Tempre*
1738309212	6 Pkt	14.06 V	7 DegC
1738308606	6 Pkt	14.06 V	6.5 DegC
1738308007	6 Pkt	13.86 V	6 DegC
1738307404	6 Pkt	13.4 V	5.5 DegC
1738306805	6 Pkt	13.12 V	4.5 DegC
1738306201	6 Pkt	12.52 V	3.5 DegC
1738305601	13 Pkt	12.38 V	2.5 DegC
1738304988	8 Pkt	12.38 V	2 DegC
1738304388	7 Pkt	12.36 V	2 DegC
1738303785	6 Pkt	12.38 V	2.5 DegC
1738303185	6 Pkt	12.38 V	2.5 DegC
1738302582	8 Pkt	12.4 V	2.5 DegC
1738301982	6 Pkt	12.38 V	2.5 DegC
1738301379	6 Pkt	12.38 V	2.5 DegC
1738300779	8 Pkt	12.4 V	2.5 DegC
1738300176	8 Pkt	12.38 V	2.5 DegC
1738299577	8 Pkt	12.4 V	3 DegC
1738298974	8 Pkt	12.38 V	3 DegC
1738298374	6 Pkt	12.42 V	3 DegC
1738297771	6 Pkt	12.42 V	3 DegC
1738297171	6 Pkt	12.42 V	3.5 DegC
1738296568	12 Pkt	12.42 V	3.5 DegC
1738295966	6 Pkt	12.42 V	4 DegC
1738295349	6 Pkt	12.42 V	4 DegC
1738294749	10 Pkt	12.44 V	4 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)