APRS.ro MAP

Reset

reset

SR0L Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR0L. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	MaxLsb*	MaxMsb*	LastTempr*	Vbatt*
1737241975	157 Raw	25 Raw	23.75 DegC	13 V
1737241346	131 Raw	25 Raw	23.75 DegC	13.04 V
1737240717	133 Raw	25 Raw	23.75 DegC	13.04 V
1737240089	133 Raw	25 Raw	23.75 DegC	12.98 V
1737239459	133 Raw	25 Raw	23.75 DegC	13.04 V
1737238831	139 Raw	25 Raw	23.75 DegC	13 V
1737238194	142 Raw	25 Raw	23.75 DegC	13 V
1737237565	163 Raw	25 Raw	23.75 DegC	13.02 V
1737236936	153 Raw	25 Raw	23.75 DegC	13.04 V
1737236311	165 Raw	25 Raw	23.75 DegC	13.02 V
1737235686	175 Raw	25 Raw	23.75 DegC	12.96 V
1737235057	185 Raw	25 Raw	23.75 DegC	13.02 V
1737234428	207 Raw	25 Raw	23.75 DegC	12.96 V
1737233789	200 Raw	25 Raw	23.75 DegC	13.04 V
1737233157	223 Raw	25 Raw	23.75 DegC	13.04 V
1737232528	219 Raw	25 Raw	23.75 DegC	13.04 V
1737231899	224 Raw	25 Raw	23.75 DegC	13.04 V
1737231270	238 Raw	25 Raw	23.75 DegC	13.04 V
1737230645	5 Raw	26 Raw	23.75 DegC	13.02 V
1737230016	1 Raw	26 Raw	23.75 DegC	12.96 V
1737229377	246 Raw	25 Raw	23.75 DegC	13 V
1737228749	250 Raw	25 Raw	23.75 DegC	13.02 V
1737228111	224 Raw	25 Raw	23.75 DegC	13.04 V
1737227482	231 Raw	25 Raw	23.75 DegC	13 V
1737226853	238 Raw	25 Raw	23.75 DegC	13.04 V

*Used Equation Coefficients:

MaxLsb: 0, 1, 0

MaxMsb: 0, 1, 0

LastTempr: 0, 0.25, -40

Vbatt: 0, 0.02, 10

PtSts: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)