APRS.ro MAP

Reset

reset

MB7UNE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UNE-10. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Vin*	Dg1h*	Eff1h*
1738325388	13.5 C	13.88 Volt	20 Pkt	95
1738324789	13 C	13.88 Volt	30 Pkt	94
1738324788	13 C	13.88 Volt	30 Pkt	94
1738324188	13 C	13.88 Volt	20 Pkt	92
1738323588	13 C	13.88 Volt	30 Pkt	92
1738322989	13 C	13.88 Volt	30 Pkt	93
1738322988	13 C	13.88 Volt	30 Pkt	93
1738322388	13 C	13.88 Volt	20 Pkt	95
1738321788	13 C	13.88 Volt	20 Pkt	94
1738321189	13 C	13.88 Volt	20 Pkt	96
1738321188	13 C	13.88 Volt	20 Pkt	96
1738320588	12.5 C	13.88 Volt	20 Pkt	97
1738319988	12.5 C	13.88 Volt	20 Pkt	98
1738319389	12.5 C	13.88 Volt	20 Pkt	98
1738319388	12.5 C	13.88 Volt	20 Pkt	98
1738318788	13 C	13.88 Volt	20 Pkt	98
1738318188	12.5 C	13.88 Volt	30 Pkt	97
1738317589	12.5 C	13.88 Volt	20 Pkt	97
1738317588	12.5 C	13.88 Volt	20 Pkt	97
1738316988	13 C	13.88 Volt	30 Pkt	97
1738316388	12.5 C	13.88 Volt	30 Pkt	97
1738315789	13 C	13.88 Volt	20 Pkt	96
1738315788	13 C	13.88 Volt	20 Pkt	96
1738315188	13 C	13.88 Volt	20 Pkt	96
1738314588	13 C	13.88 Volt	20 Pkt	98

*Used Equation Coefficients:

Temp: 0, 0.5, -64

Vin: 0, 0.075, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)