APRS.ro MAP

Reset

reset

SR9WXL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXL. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1737224129	88 Pkt	5 Pkt	1 Pkt
1737223526	102 Pkt	2 Pkt	0 Pkt
1737222926	112 Pkt	8 Pkt	4 Pkt
1737222321	109 Pkt	3 Pkt	1 Pkt
1737221722	107 Pkt	4 Pkt	0 Pkt
1737221119	103 Pkt	2 Pkt	0 Pkt
1737220518	135 Pkt	4 Pkt	1 Pkt
1737219916	161 Pkt	7 Pkt	0 Pkt
1737219303	124 Pkt	3 Pkt	0 Pkt
1737218102	146 Pkt	6 Pkt	3 Pkt
1737217499	111 Pkt	4 Pkt	2 Pkt
1737216899	121 Pkt	4 Pkt	0 Pkt
1737216294	128 Pkt	5 Pkt	3 Pkt
1737215092	130 Pkt	8 Pkt	6 Pkt
1737214492	137 Pkt	4 Pkt	1 Pkt
1737213890	113 Pkt	4 Pkt	1 Pkt
1737213287	101 Pkt	5 Pkt	2 Pkt
1737212085	122 Pkt	4 Pkt	1 Pkt
1737211482	96 Pkt	2 Pkt	0 Pkt
1737210882	116 Pkt	8 Pkt	0 Pkt
1737210268	97 Pkt	2 Pkt	0 Pkt
1737209667	116 Pkt	6 Pkt	2 Pkt
1737209064	119 Pkt	3 Pkt	1 Pkt
1737208464	88 Pkt	4 Pkt	1 Pkt
1737207861	94 Pkt	4 Pkt	1 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)