APRS.ro MAP

Reset

reset

TA1DX-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA1DX-4. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1737252983	1 Pkt	-40 dBm	15.22 V
1737252673	3 Pkt	-39 dBm	15.26 V
1737252363	1 Pkt	-40 dBm	15.22 V
1737252053	1 Pkt	-39 dBm	15.22 V
1737251743	1 Pkt	-40 dBm	15.22 V
1737251433	1 Pkt	-40 dBm	15.22 V
1737251123	1 Pkt	-40 dBm	15.22 V
1737250813	3 Pkt	-40 dBm	15.22 V
1737250503	1 Pkt	-40 dBm	15.26 V
1737250193	1 Pkt	-40 dBm	15.26 V
1737249883	1 Pkt	-40 dBm	15.22 V
1737249573	1 Pkt	-40 dBm	15.26 V
1737249263	1 Pkt	-40 dBm	15.26 V
1737248953	2 Pkt	-40 dBm	15.22 V
1737248643	1 Pkt	-40 dBm	15.22 V
1737248333	2 Pkt	-40 dBm	15.22 V
1737248023	1 Pkt	-40 dBm	15.22 V
1737247713	0 Pkt	-40 dBm	15.26 V
1737247403	4 Pkt	-39 dBm	15.22 V
1737247093	1 Pkt	-39 dBm	15.26 V
1737246783	0 Pkt	-40 dBm	15.22 V
1737246473	2 Pkt	-39 dBm	15.22 V
1737246163	1 Pkt	-40 dBm	15.22 V
1737245853	0 Pkt	-40 dBm	15.26 V
1737245543	4 Pkt	-40 dBm	15.26 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)