APRS.ro MAP

Reset

reset

IR3EO-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR3EO-11. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1737229196	144 Pkt	960 Pkt	12.01 Volt
1737228896	136 Pkt	1000 Pkt	12.01 Volt
1737228596	133 Pkt	1000 Pkt	12.01 Volt
1737228296	149 Pkt	1010 Pkt	12.01 Volt
1737227996	139 Pkt	1030 Pkt	12.01 Volt
1737227696	121 Pkt	1030 Pkt	12.01 Volt
1737227396	142 Pkt	1050 Pkt	12.01 Volt
1737227096	157 Pkt	1070 Pkt	12.01 Volt
1737226796	154 Pkt	1050 Pkt	12.01 Volt
1737226496	157 Pkt	1070 Pkt	12.01 Volt
1737226196	168 Pkt	1060 Pkt	12.01 Volt
1737225896	185 Pkt	1040 Pkt	12.01 Volt
1737225597	156 Pkt	1020 Pkt	12.01 Volt
1737225297	155 Pkt	1000 Pkt	12.01 Volt
1737224997	161 Pkt	1000 Pkt	12.01 Volt
1737224697	169 Pkt	1010 Pkt	12.01 Volt
1737224397	144 Pkt	980 Pkt	12.01 Volt
1737224097	155 Pkt	990 Pkt	12.01 Volt
1737223797	153 Pkt	1010 Pkt	12.01 Volt
1737223497	161 Pkt	1000 Pkt	12.01 Volt
1737223197	153 Pkt	990 Pkt	12.01 Volt
1737222897	135 Pkt	1000 Pkt	12.01 Volt
1737222597	135 Pkt	990 Pkt	12.01 Volt
1737222297	140 Pkt	1000 Pkt	12.01 Volt
1737221997	139 Pkt	990 Pkt	12.01 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Volt: 0, 0.079, 0

DgR: 0, 0.001, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)