APRS.ro MAP

Reset

reset

SR9NLI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NLI. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Visc10min*	Vbatt*
1737226287	56 Pkt	0 Pkt	14.28 V
1737225687	49 Pkt	0 Pkt	14.26 V
1737225083	56 Pkt	0 Pkt	14.26 V
1737224189	44 Pkt	0 Pkt	14.28 V
1737223588	46 Pkt	0 Pkt	14.26 V
1737222988	45 Pkt	0 Pkt	14.22 V
1737222387	48 Pkt	0 Pkt	14.24 V
1737221774	37 Pkt	0 Pkt	14.22 V
1737221174	38 Pkt	0 Pkt	14.2 V
1737220573	54 Pkt	0 Pkt	14.28 V
1737219973	49 Pkt	0 Pkt	14.24 V
1737219373	61 Pkt	0 Pkt	14.26 V
1737218772	53 Pkt	0 Pkt	14.26 V
1737218172	57 Pkt	0 Pkt	14.28 V
1737217572	46 Pkt	0 Pkt	14.26 V
1737216971	66 Pkt	0 Pkt	14.26 V
1737216371	66 Pkt	0 Pkt	14.28 V
1737215770	55 Pkt	0 Pkt	14.24 V
1737215170	56 Pkt	0 Pkt	14.18 V
1737214570	73 Pkt	5 Pkt	14.26 V
1737213969	50 Pkt	0 Pkt	14.28 V
1737212794	40 Pkt	0 Pkt	14.28 V
1737212193	41 Pkt	0 Pkt	14.24 V
1737211593	50 Pkt	0 Pkt	14.28 V
1737210990	55 Pkt	0 Pkt	14.26 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)