APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

SR8WXO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXO. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1732237629	73 Pkt	6 Pkt	4 Pkt
1732237026	86 Pkt	5 Pkt	3 Pkt
1732236423	58 Pkt	10 Pkt	4 Pkt
1732235813	82 Pkt	6 Pkt	4 Pkt
1732235211	79 Pkt	6 Pkt	4 Pkt
1732234608	77 Pkt	7 Pkt	5 Pkt
1732234005	95 Pkt	10 Pkt	4 Pkt
1732233395	87 Pkt	5 Pkt	3 Pkt
1732232792	83 Pkt	9 Pkt	7 Pkt
1732232189	81 Pkt	7 Pkt	5 Pkt
1732231587	87 Pkt	11 Pkt	5 Pkt
1732230977	78 Pkt	7 Pkt	5 Pkt
1732230374	97 Pkt	6 Pkt	4 Pkt
1732229771	81 Pkt	5 Pkt	3 Pkt
1732229168	88 Pkt	10 Pkt	4 Pkt
1732228559	82 Pkt	9 Pkt	7 Pkt
1732227956	88 Pkt	6 Pkt	4 Pkt
1732227353	66 Pkt	7 Pkt	5 Pkt
1732226750	99 Pkt	12 Pkt	6 Pkt
1732226140	100 Pkt	6 Pkt	4 Pkt
1732225538	109 Pkt	11 Pkt	9 Pkt
1732224935	130 Pkt	19 Pkt	17 Pkt
1732224332	98 Pkt	14 Pkt	8 Pkt
1732223722	139 Pkt	15 Pkt	13 Pkt
1732222516	105 Pkt	8 Pkt	6 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)