APRS.ro MAP

Reset

reset

DD3UTS-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DD3UTS-15. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	DrehWin*	BlitzD*
1738300831	13.05 V	152 n/min	100 km
1738300531	13.05 V	156 n/min	100 km
1738300232	13.05 V	116 n/min	100 km
1738299931	13.05 V	228 n/min	100 km
1738299631	13.05 V	208 n/min	100 km
1738299333	13.05 V	184 n/min	100 km
1738299031	13.05 V	168 n/min	100 km
1738298732	13.05 V	196 n/min	100 km
1738298432	13.05 V	104 n/min	100 km
1738298132	13.05 V	156 n/min	100 km
1738297832	13.05 V	88 n/min	100 km
1738297531	13.05 V	152 n/min	100 km
1738297232	13.05 V	140 n/min	100 km
1738296932	13.05 V	40 n/min	100 km
1738296631	13.05 V	8 n/min	100 km
1738296332	13.05 V	16 n/min	100 km
1738296032	13.05 V	20 n/min	100 km
1738295731	13.05 V	4 n/min	100 km
1738295431	13.05 V	52 n/min	100 km
1738295132	13.05 V	68 n/min	100 km
1738294831	13.05 V	20 n/min	100 km
1738294531	13.05 V	12 n/min	100 km
1738294231	13.05 V	8 n/min	100 km
1738293931	13.05 V	16 n/min	100 km
1738293631	13.05 V	32 n/min	100 km

*Used Equation Coefficients:

Battery: 0, 0.075, 0

DrehWin: 0, 4, 0

SolarP: 0, 4, 0

BlitzD: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)