APRS.ro MAP

Reset

reset

DM0DOS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DM0DOS-10. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Vin*	Temp*
1737226218	1460 Pkt	12.38 Volt	4 C
1737225618	1500 Pkt	12.38 Volt	4 C
1737225018	1490 Pkt	12.38 Volt	4 C
1737224418	1540 Pkt	12.38 Volt	4 C
1737223818	1490 Pkt	12.38 Volt	3.5 C
1737223218	1500 Pkt	12.38 Volt	3.5 C
1737222618	1530 Pkt	12.38 Volt	3.5 C
1737222018	1530 Pkt	12.38 Volt	3.5 C
1737221418	1480 Pkt	12.38 Volt	3.5 C
1737220818	1470 Pkt	12.38 Volt	3.5 C
1737220218	1470 Pkt	12.38 Volt	3.5 C
1737219618	1430 Pkt	12.38 Volt	3 C
1737219018	1410 Pkt	12.38 Volt	3 C
1737218418	1430 Pkt	12.38 Volt	3 C
1737217818	1490 Pkt	12.38 Volt	3 C
1737217218	1530 Pkt	12.38 Volt	3 C
1737216618	1550 Pkt	12.38 Volt	3 C
1737216018	1550 Pkt	12.38 Volt	3 C
1737215418	1550 Pkt	12.38 Volt	3 C
1737214818	1550 Pkt	12.38 Volt	3 C
1737214218	1530 Pkt	12.38 Volt	3 C
1737213618	1520 Pkt	12.38 Volt	3 C
1737213018	1520 Pkt	12.38 Volt	2.5 C
1737212418	1540 Pkt	12.38 Volt	2.5 C
1737211818	1580 Pkt	12.38 Volt	2.5 C

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Vin: 0, 0.075, 0

Temp: 0, 0.5, -64

Value4: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)