APRS.ro MAP

Reset

reset

IQ3TS-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ3TS-11. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1737203161	35 Pkt	340 Pkt	14.22 Volt
1737202861	47 Pkt	350 Pkt	14.22 Volt
1737202561	52 Pkt	350 Pkt	14.22 Volt
1737202261	51 Pkt	350 Pkt	14.22 Volt
1737201961	50 Pkt	340 Pkt	14.22 Volt
1737201661	66 Pkt	350 Pkt	14.22 Volt
1737201361	54 Pkt	350 Pkt	14.22 Volt
1737201061	57 Pkt	330 Pkt	14.22 Volt
1737200761	61 Pkt	340 Pkt	14.22 Volt
1737200461	49 Pkt	340 Pkt	14.22 Volt
1737200161	60 Pkt	340 Pkt	14.22 Volt
1737199861	59 Pkt	330 Pkt	14.22 Volt
1737199561	50 Pkt	330 Pkt	14.22 Volt
1737199261	48 Pkt	310 Pkt	14.22 Volt
1737198961	48 Pkt	310 Pkt	14.22 Volt
1737198661	52 Pkt	310 Pkt	14.22 Volt
1737198361	57 Pkt	300 Pkt	14.22 Volt
1737198061	40 Pkt	280 Pkt	14.22 Volt
1737197761	50 Pkt	280 Pkt	14.22 Volt
1737197461	65 Pkt	270 Pkt	14.22 Volt
1737197161	54 Pkt	260 Pkt	14.22 Volt
1737196861	35 Pkt	240 Pkt	14.22 Volt
1737196561	49 Pkt	250 Pkt	14.22 Volt
1737196261	41 Pkt	240 Pkt	14.22 Volt
1737195961	35 Pkt	240 Pkt	14.22 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

DgR: 0, 0.001, 0

Volt: 0, 0.079, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)