APRS.ro MAP

APRS.ro MAP About ☰ --:--:--

Reset

reset

SR9WXJ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXJ. If no packets are shown the sender has not sent any telemetry packets the latest 2 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Rx10min*	Digi10min*	Vbatt*
1732203261	48 Pkt	1 Pkt	11.34 V
1732202658	44 Pkt	0 Pkt	11.38 V
1732202054	49 Pkt	0 Pkt	11.4 V
1732201452	60 Pkt	0 Pkt	11.44 V
1732200849	52 Pkt	0 Pkt	11.38 V
1732200246	54 Pkt	0 Pkt	11.5 V
1732199643	37 Pkt	0 Pkt	11.58 V
1732199040	51 Pkt	0 Pkt	12.08 V
1732198437	51 Pkt	0 Pkt	12.6 V
1732197834	56 Pkt	0 Pkt	12.1 V
1732197231	57 Pkt	0 Pkt	11.54 V
1732196628	51 Pkt	0 Pkt	11.9 V
1732196025	41 Pkt	0 Pkt	11.7 V
1732189577	36 Pkt	0 Pkt	11.28 V
1732188973	39 Pkt	0 Pkt	11.38 V
1732188371	32 Pkt	0 Pkt	11.44 V
1732187768	48 Pkt	0 Pkt	11.44 V
1732187165	40 Pkt	0 Pkt	11.52 V
1732167404	45 Pkt	0 Pkt	11.12 V
1732163908	36 Pkt	0 Pkt	11.2 V
1732136459	12 Pkt	0 Pkt	11.24 V
1732135859	7 Pkt	0 Pkt	11.26 V
1732135259	4 Pkt	0 Pkt	11.3 V
1732134659	3 Pkt	0 Pkt	11.32 V
1732134058	6 Pkt	0 Pkt	11.4 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)